300-360 Exam Study Guide | Cisco 300-360 exam dumps with correct answers
pass4itsure Cisco 300-360 exam questions with accurate answers. Try to download 300-360 free demo first: https://www.pass4itsure.com/300-360.html..
Share a free Cisco 300-360 exam pdf downloads:
https://drive.google.com/open?id=1qem16vJ_9v7ydlXw8i74jmuYjc96ohPk
What you’ll learn
300-360 WIDESIGN
Certification: CCNP Wireless
Duration: 90 minutes (55 – 65 questions)
Available languages: English
- Determine customer Wi-Fi design process
- Design for data coverage
- Design for voice and real-time applications
- Design for location and Cisco CMX
- Design for Wi-Fi beyond the enterprise campus
- Describe how to conduct a site survey
Requirements
- Self-Study E-Learning
- Instructor Led Training
- Cisco Press
Study material list
Obtaining Customer Requirements as related to the WLAN Installation
Cisco CleanAir Technology |
Survey Tools |
Site Survey Guidelines for WLAN Deployment |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Determine facility type and constraints Related to WLAN Deployments
Site Survey Guidelines for WLAN Deployment |
Wireless LAN Design Guide for High Density Client Environments in Higher Education |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
WLAN Predictive Design
Cisco Wireless with the Ekahau Real-Time Location System (RFID over Wi-Fi) |
Site Survey Guidelines for WLAN Deployment |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Pre-deployment site survey
Improving Air Quality with Cisco CleanAir |
Site Survey Guidelines for WLAN Deployment |
Cisco Wireless Mesh Access Points, Design and Deployment Guide, Release 8.1 |
Indoor Mesh Deployment Guide |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Post-deployment site survey
Post-Deployment Radio Frequency Tuning |
Cisco Prime Infrastructure 3.0 Reference Guide |
Cisco Prime Infrastructure 3.0 Administrator Guide |
Cisco Prime Infrastructure 3.0 User Guide |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Design the infrastructure of the wireless network
Power over Ethernet (PoE) Power Requirements FAQ |
IPv6 First-Hop Security Configuration Guide, Cisco IOS XE Release 3S |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Describe and Design Wireless architecture for Real time applications
Designing the Wireless LAN for Cisco Jabber |
Design Principles for Voice over WLAN |
Understanding IP Telephony Protocols |
WLAN RF Design Considerations |
Designing Cisco Wireless Enterprise Networks (WIDESIGN) v1.1CLN Store Content |
Bought(book) pass Cisco 300-360 exam
“CCNP Wireless CUWSS Quick Reference D. J. Henry”
“Controller-Based Wireless LAN Fundamentals: An End-to-end Reference Guide to Design, Deploy, Manage, and Secure 802.11 Wireless Networks Jeff Smith”
Actual Cisco Questions And Answers 300-360
QUESTION 1
The ClO of a company wants to start tracking inventory in the warehouse using RFID tags and their existing wireless
network.
The company hires a wireless engineer to ensure that their existing network can support this new initiative. Which tool in
Cisco Prime can help the wireless engineer?
A. Planning Mode
B. Map Editor
C. Site Survey
D. Location Readiness
Correct Answer: D
Using Chokepoints to Enhance Tag Location Reporting Installation of chokepoints provides enhanced location
information for RFID tags. When an active Cisco- compatible Extensions Version 1-compliant RFID tag enters the range
of a chokepoint, it is stimulated by the chokepoint. The MAC address of this chokepoint is then included in the next
beacon sent by the stimulated tag. All access points that detect this tag beacon then forward the information to the
controller and location appliance.
https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/3-0/user/guide/pi_ug/wireless-map s.html#91300
QUESTION 2
When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to
support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Correct Answer: A
QUESTION 3
An engineer is tasked with designing a WLAN. The customer is prioritizing data speeds to the desktop, but is also
entertaining the idea of adding 802.11 phones in the future. Given this information, how should the engineer conduct the
survey?
A. consider the employee head count in congested office space and limit the edge of each cell to an RSSI of -67mW
B. restrict AP cell edges to -67dB and be sure to strategically place APs in congested office spaces
C. co-locate access points when possible to cover high user areas and place APs at each corner of the facility
D. stagger the AP placements, and be sure to have a high signal to noise ratio that will accommodate the future VoIP
devices
Correct Answer: B
QUESTION 4
After implementing mesh with an IP surveillance camera connected to the LAN port on a RAP, the engineer notices that
QoS is not being marked. In this setup, what device is responsible for marking upstream traffic from the camera?
A. IP Camera
B. MAP
C. RAP
D. Wireless Controller
E. First-Hop Router
Correct Answer: A
QUESTION 5
Which two factors influence the density of APs in a data-only WLAN environment? (Choose two.)
A. the number of clients that will roam through the facility
B. the type of controller chosen
C. the defined coverage area and customer needs
D. the number of APs dedicated to voice services
E. channel reuse and WLAN bandwidth
Correct Answer: CE
QUESTION 6
A customer is deploying a Greenfield 802.11ac network on a floor that will support approximately 300 wireless devices.
Which setting needs to be changed on Prime Infrastructure Planning Tool in order to predict the amount of access
points the customer needs to service the new floor?
A. Data Coverage Support Margin
B. Demand Settings
C. Add AP Field
D. 802.11n Protocol Support
Correct Answer: C
http://www.cisco.com/c/en/us/td/docs/wireless/prime_infrastructure/1-2/configuration/guide/pi_12_cg/
maps.html#pgfId-1671104
QUESTION 7
You must perform a Layer1 survey by using Metageek Chanalyzer on the current operating mode is configured for
Cisco CleanAir AP?
A. Local
B. SE-connect
C. Monitor
D. Sniffer
Correct Answer: A
QUESTION 8
An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to
when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Correct Answer: A
QUESTION 9
The AP has been configured property for a VoWLAN survey. The RF environment contains a noise of -87 to -90 dBm.
What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Correct Answer: A
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-1/Enterprise-Mobility-8-1-Design-Guide/Enterprise_Mobility_8-1_Deployment_Guide/Chapter-9.html Cisco guidelines for deploying 802.11b/g/a VoWLAN
handsets recommend a design where a minimum power of -67 dBm is present at the cell boundary (see Figure 9-10).
This practice creates cell sizes that are smaller than those used in data WLAN designs of the past. The -67 dBm
threshold is a general recommendation for achieving a packet error of one percent, which requires an SNR value of 25
dB or greater (local noise conditions impact this requirement).
QUESTION 10
Which infrastructure issue needs to be verified and potentially resolved before deploying a centralized 802.11n WLAN?
A. That all the access layer switches that the 802.11n APs will connect to support 802.3af power.
B. That all the access layer switches that the 802.11n APs will connect to contain 10/100/1000 Ethernet ports.
C. The location of application and authentication servers.
D. The proposed location for the WDS server.
E. The proposed location for the WCS.
Correct Answer: B
QUESTION 11
Anetwork engineer is performing a site survey in preparation for an installation. Which three hardware parameters must
be inspected? (Choose three.)
A.routing protocol used
B.PoE capability
C.switch STP capability
D.distance of antenna to communications room
E.switch port availability
F.distance of access point to communications room
Correct Answer: BEF
QUESTION 12
A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows
significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be
excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?
A. 132
B. 44
C. 11
D. 36
Correct Answer: A
Weather radars operate within the 5600-to 5650-MHz band, which means that channels 124 and 128 might be affected,
but also channels 120 and 132 might suffer from weather radar activity. http://www.cisco.com/ c/en/us/td/docs/wireless/
technology/mesh/7-3/design/guide/Mesh/ Mesh_chapter_0111.html
QUESTION 13
An engineer is surveying a customer site for additional wireless coverage. Which two menus will engineer navigate to in
order to determine the maximum number of supported APs? (Choose two.)
A. Monitor ?Access Points
B. Wireless ?Access Points
C. Management ?Summary
D. Controller ?Inventory
E. Monitor ?Summary
Correct Answer: CD
Summarize:
If you want comprehensive and concise information about Cisco 300-360 Exam then your exam preparation should be started with these Authentic Cisco 300-360 Exam Dumps PDF. These reference questions answers are designed under the surveillance of Professionals and Experts. You can rely on them without any hesitation. More you would read these 300-360 dumps, more things you would know.please click: https://www.pass4itsure.com/300-360.html.